UAS Teardown(LAB11)

 My team had a chance to teardown UAS for this two-week lab. It was a lot more complicated than I thought. And some parts of our drone were already missing from the get-go, we were confused at first but we ended up tearing down ours perfectly.


This is the process for teardown.


Tear-Down Instructions:


1: Take Screws out of the center plastic that holds the harness w/ Phillips screwdriver (4 Screws)


2: Take Velcro Senor Harness off


3: Unplug Wires from Wire Hub


  • 1, 2, 3, 4 , RCN

  • Power2, USB, GPS 1

4: Unscrew/Take off Wire Hub


5: Unscrew and Take Off Plate/Assembly that holds the GPS station


6: Unscrew GPS Holder/Tower


7: Remove GPS sensor from GPS holder/tower


8: Cut the zip ties on the SimonK 30A

9: Cut the zip ties on the propeller arms


10: Unscrew and remove the top and bottom screws from the motor mounts


11: Remove Channel Receiver


12: Unscrew and Remove Prop Arms


13: Separate Central Square Plastic Mounts by removing the screws on both sides and the spacers in-between


14. Unscrew the screws in the Central Square Plastic Mounts from the Landing Gear Attachments


15. Disconnect Landing Gear Supports from Landing Gear Attachments


16. Remove screws from the Central Plastic Mount


17. Disconnect the Circuit Board from the Central Plastic Mount


18. Do Solder the cords/wires from Circuit Board







Comments

Post a Comment

Popular posts from this blog

Final project(UAS data mapping mission)

Image
Required for the mission:         Mobile device with supporting mission planning software          A UAS Platform/Sensor of your choice I was asked to fly an assigned mission plot at PWA with this parameter. Altitude: 122m Lateral and Frontal Overlap: 80% Use the search function to find and open the Add Z Information (3D Analyst Tools) tool. This tool calculates properties of 3D shapes and appends the result to the attribute table of the input feature class. In this step, you will calculate the length of each sight line. Set the following parameters: Input Features: LOS_Lines Output Property: 3-Dimensional Length      The purpose of this project is to conduct a UAV mission to collect aerial imagery and data for a specific area at PWA(Purdue wildlife Area). The mission area has been assigned and the goal was to fly the assigned mission area while ensuring that the flight boundaries are slightly larger than the assigned area to...
Read more

Volumetric analysis with UAS Data

Image
In a previous lab, I completed some ESRI tutorials regarding raster data analysis. This time, I engaged in raster data analysis using UAS data gathered over the course of a mine dredging operation. I needed to draw upon what I've learned in the ESRI tutorials so far. ·        Extract by mask This tool extracts the cells of a raster that correspond to the areas defined by a mask. The mask is typically a raster dataset where cells with a certain value represent the areas I want to extract. ·          Resample Resampling is the process of changing the resolution of a raster dataset. ·          Surface volume The Surface Volume tool calculates the volume between two surfaces. I began on the 4 th of July to where the mine operation tells of the dredging to take place, and for me to establish a base dataset to know how much material was added. They are also concerned about slope fai...
Read more

Performing Line of Sight Analysis by Esri

Image
Performing Line of Sight Analysis by Esri Use the search function to find and open the Construct Sight Lines (3D Analyst Tools) tool. In the Geoprocessing pane, set the following parameters: Observer Points: Observers Target Features: ParadeRoute Output: ..\EsriTraining\ProLineSight\MyData\MyData.gdb\ SightLines Observer Height Field: SHAPE.Z Target Height Field: SHAPE.Z Sampling Distance:  30 Use the search function to find and open the Line Of Sight (3D Analyst Tools) tool. Set the following parameters: Input Surface: Elevation Input Line Features: SightLines Input Features: Buildings_subset Output Feature Class: ..\EsriTraining\ProLineSight\MyData\MyData.gdb\ LOS_Lines Use the search function to find and open the Add Z Information (3D Analyst Tools) tool. This tool calculates properties of 3D shapes and appends the result to the attribute table of the input feature class. In this step, you will calculate the length of each sight line.  Set the following parameters: Input Fe...
Read more